Nutrafin CO2 - Equipment - Aquatic Plant Central

Go Back   Aquatic Plant Central > General Interest Forums > Equipment

Equipment Aquarium Equipment - Discuss equipment to help setup your planted aquarium.

Reply
 
LinkBack Thread Tools Display Modes
Old 09-20-2008, 04:14 PM   #1 (permalink)
Member
 
Join Date: Aug 2008
Posts: 34
iTrader Ratings: 0
flora is a regular member
Default Nutrafin CO2

Hi guys!
I finally have my tank set up. Did it last night. I have a Nutrafin {something like DIY} system for CO2. It has one of those little ladders that the co2 bubbles are supposed to go through. It took 12 hours for me to notice the first bubble. How fast should it be producing CO2? I have also noticed that sometimes the bubbles don't get all the way up the ladder. Sometimes one just sits there, then the next one comes along and clings to the first one making a very large bubble. Is this normal? I don't have a lot of surface agitation but as soon as the bubble(s) do come out they go straight to the surface. It seems that there is only a few bubbles per hour. Shouldn't there be more than that?
flora is offline   Reply With Quote

Advertisement [Remove Advertisement]
Old 09-20-2008, 07:30 PM   #2 (permalink)
Senior Member
 
trenac's Avatar
 
Join Date: Jul 2004
Location: North Carolina
Posts: 7,464
iTrader Ratings: 25
iTrader Positive Rating: 100%
trenac is a valuable member of the community trenac is a valuable member of the community trenac is a valuable member of the community
Default Re: Nutrafin CO2

I can take up to 24 hours to start producing bubbles. Until the ladder gets some gunk built up the bubbles will stick. So both of these things are normal. If Ii remember correctly there is no way to control the bubble count. So the amount of bubbles you get is dependent on the mixture packets. You should however be getting more then a few an hour. It could be that it's only been 12 hours. Give it another day & see what happens.



trenac is offline   Reply With Quote
Old 09-20-2008, 07:36 PM   #3 (permalink)
Senior Member
 
gheitman's Avatar
 
Join Date: Aug 2007
Location: Champaign, Illinois
Posts: 299
iTrader Ratings: 9
iTrader Positive Rating: 100%
gheitman is a regular member
Default Re: Nutrafin CO2

I use these and what Trena said was right. It can take a day or more for the bubble counter/ladder to allow bubbles to go all the way to the top without stopping. You should get to the point where there will be several bubbles going up the ladder at the same time. One thing you might want to do is check and make sure the lid is on tight but still able to be turned. If the lid isn't tightened down you could get CO2 escaping.
gheitman is offline   Reply With Quote
 
Old 09-21-2008, 09:58 AM   #4 (permalink)
Member
 
Join Date: Aug 2008
Posts: 34
iTrader Ratings: 0
flora is a regular member
Default Re: Nutrafin CO2

Thanks, but my next question is, is the time that it takes for the bubbles to go up the ladder enough time for co2 to be imparted into the water column? After the bubbles make it through the ladder they go straight to the top and pop! Is this the way it is supposed to operate? I'm adding excel also.
flora is offline   Reply With Quote
Old 09-21-2008, 10:01 AM   #5 (permalink)
Senior Member
 
gheitman's Avatar
 
Join Date: Aug 2007
Location: Champaign, Illinois
Posts: 299
iTrader Ratings: 9
iTrader Positive Rating: 100%
gheitman is a regular member
Default Re: Nutrafin CO2

That is the way it is supposed to operate. You may have noticed that the bubbles are getting smaller as they rise up the ladder. This is because the CO2 is being absorbed into the water. They don't disappear completely though. I also combine the Hagen CO2 setup with Flourish Excel on two of my larger tanks.
gheitman is offline   Reply With Quote
Old 09-21-2008, 01:58 PM   #6 (permalink)
Member
 
Join Date: Aug 2008
Posts: 34
iTrader Ratings: 0
flora is a regular member
Default Re: Nutrafin CO2

Well,
Being the impatient type that I am, I mixed up my own yeast, sugar and water solution. I put the sugar up to the first level, then added a 1/4 tsp. of yeast, and filled it up to the 2nd
level with water. The bubbles took a couple of hours to start, but my gosh they're coming one right after the other! Do you really need the stabilizer packet? We have well water and it is extremely hard. Sorry for all the questions, but I love this forum. So far everyone has been nothing but helpful!
flora is offline   Reply With Quote
Old 09-21-2008, 03:20 PM   #7 (permalink)
Senior Member
 
gheitman's Avatar
 
Join Date: Aug 2007
Location: Champaign, Illinois
Posts: 299
iTrader Ratings: 9
iTrader Positive Rating: 100%
gheitman is a regular member
Default Re: Nutrafin CO2

The stabilizer packet, which can be replaced by pure baking soda when you run out, is needed to make sure that the fermenting process doesn't get out of control and start sending the byproducts of fermentation into your aquarium.
gheitman is offline   Reply With Quote
Reply


Aquatic Plant Central > General Interest Forums > Equipment > Nutrafin CO2

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 08:28 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.

Search Engine Friendly URLs by vBSEO 3.6.1