Aquatic Plant Forum banner

DIY 29 Gallon Hood

37K views 22 replies 10 participants last post by  Cliff Mayes 
#1 · (Edited)
Here is how I build my hood for my 29 gallon aquarium.

Supplies:
1x6 and 1x8 pine boards.
2 hinges (or a piano hinge)
Wood glue
Finishing nails ~2"
Nail filler
Sandpaper
Paint (or stain)

I started by cutting my boards to length. I would recommend getting your wood from an actual lumber yard rather than Lowe's or home depot. You will save yourself lots of time and headache trying to find nice straight boards. There are two variations of hoods I have built. I will describe one of them here first and the second later on.

There are total of 7 boards used...

Face board: 31 3/4" X 6"
Front top: 31 3/4" x 6"
Back top: 31 3/4" x 8"
Front side (2) ~4 5/8" by 6"
Back side (2) ~4 5/8" by 8"
Note: 6" boards are not really 6". They are something like 5 1/2"
The back is left open in my hoods. You could some sort of back board for extra support if you would like. I didn't see a need for it.




As you can see the front half is attached by two hinges to the back half. One piano hinge could also be used.

After the boards were cut to length I began assembling the two halves. I used glue and a nail gun with 2" brads. Regular nails can be used. You may want to consider seating the nails below the surface and using nail filler to get a nice finish. I find that the nail gun makes things a lot easier and faster to assemble.

Note that in the picture the back half of my hood uses only a 1X6. This was a screw up on my part and I would recommend using a 1x8 so the hood covers the entire top of the aquarium.

Once the two halves were assembled, I filled the nail holes, sanded everything down good, and put on 2 or 3 coats of black paint. I then cut out notches (with a chisel) for the hinges and installed them.

I used small "L" brackets inside of the hood to keep it supported on top of the aquarium.






You are now ready to install your lights!

Another variation of this hood, which I actually think is nicer and easier to built is this...It is one I build for my 55 gallon.


You can see the difference in the photo. This one is easier to get to sit on your tank right because the sides are just 1 piece rather than two. Everything just fits together much nicer. The problem I had is that the face board warped outward. The other style prevents this because the face board is attached to the front side board. I also used a piano hinge on this hood, which is another nice touch. The hood in also taller because it need to cover some HOB filters (i.e. the face board is a 1X8 rather than a 1x6).

All in all, this will take about a 1/2 to full day to build once you consider all the time to paint and dry. Total cost is probably less than $20.
Good luck.
 
See less See more
9
#2 ·
I built the same type of hood for my 40gal. Excellent design. It allows you access to the aquarium while leaving one of the lights on. One thing I noticed with mine is that heat is somewhat of a problem, even with vents. I am thinking of adding fans to mine.
 
#15 ·
Hi Snydaleid,

Do yourself a favor and call Kim (guy) at AH Supply and talk with him. I have a 45 tall (36" X 12" X 24" H) and was advised that the 2 X 55 watt kit would be too long for my tank due to end caps, power cord, and working space constraints. He suggested that I go with the 1 X 96 watt system. I'm glad I talked with him, he was very helpful and informative. I bought the 1 X 96 watt with his 6700K bulb and couldn't be happier after almost 3 months. I can grow just about anything, even in this deep tank. Hope this information helps!
 
#19 ·
Hi Snydaleid,

I was talking with Kim at AH Supply yesterday about another matter and mentioned your post on this site. He said that he had received your email and that you were not putting the two 55 watt systems end to end but side to side. They will fit just fine that way, I misunderstood how you were planning the install. I hope you like your system as much as I like mine!
 
#20 ·
Ok finally got it all finished. I had so much goin on that I didn't have much time to put toward this. This is a pretty nice canopy. I'm really happy the way it turned out. The lights are BRIGHT! I used a piano hinge and blocks of wood instead of the L brackets. Here's what mine looks like.


 
#23 ·
I have been using the AH light fixtures for a couple of years but I bought the GE lights (from somewhere else) that everyone seems to recommend and they have been working OK for a couple of years.

A hood can be made from thin Luan that is cut with a utility knife with many cuts rather than trying to force the blade thru. Corner support can be from one bys that have been ripped into narrow strips. Do not try to use metal fasteners such as nails of screws to hold the structure together unless the metal fasteners are just to hold the boards until the glue dries. Just about any wood glue works. A shallow box is better than a deep box so make it as small as you can. Making sure that the AH kit will fit in the box is about the only problem.

Luan (which is inexpensive) or any other thin board has a lot of strength to make stands so 2 X 4's (which are also cheap) are overkill in stand making as far as holding the water weight. Even a one by six can hold a lot of weight but on a large tank it it is probably a good ides to use some larger boards. I would be more concerned with putting a large tank (very heavy) on a floor that someone has messed with. It is difficult to understand the foolishness some folks will do to an existing structure so do not get blindsided by a tank ending up in the Cellar inadvertently. It would be unusual for a small tank (10/20 gallons or less) to break thru a floor but it could happen.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top